Flexim Liquid And Gas Flow Meter_Stc Việt Nam

The FLUXUS ADM 5107 is FLEXIM''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s solution for many flow metering applications found in the water and wastewater sector and adjacent industries. As FLEXIMs basic and economic alternative, the ADM 5107 offers the same benefits in terms of accuracy and reliability as its bigger brothers, the FLUXUS ADM 7407 and ADM 8027.

The FLUXUS ADM 5107 offers a precise bi-directional flow measurement over a wide turndown ratio and not only at high, but especially at  low flow velocities due to its matched and paired transducer pairs, offering a superior zero stability, and the superior measurement algorithms embedded in the flow computer. With its water-tight IP67 transducers and a permanent coupling due, it is also thought for outside use at drinking water pipelines or similar applications and is virtually maintenance free. Especially here, at pipe diameters up to 2500 mm, it is a better and much more cost effective alternative to other measurement technologies, such as MIDs.

As of its high repeatability, the FLUXUS ADM 5107 also offers the possibility for leak detection when placing multiple measurement systems at one pipeline. Especially at night, when temperatures are more even and only low flow velocities are common in drinking water lines, leakages can clearly be identified and such reading transferred to a process control system.

As a non-intrusive clamp on flow meter, the FLUXUS ADM 5107 is the ideal solution for retrofitting in existing networks without interruption of supply lines.Thanks to the clamp-on technology, no cutting or welding work is needed to mount the transducers on the pipe. During installation, the flow meter''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s user interface is automatically adapted to the connected transducers and no zeroing is necessary. Water is already pre-selected as medium and it''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s physical properties are stored in the flowmeter''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s memory.

In most cases only the pipe''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s outer diameter and wall thickness as well as the water temperature has to be entered in order to start the measurement. The commissioning work is thus reduced to a minimum. On request, the instrument can even be pre-configured at the factory.

FLEXIM also offers flow meter solutions for complete pipeline balancing, where the flow meter can be buried underground. IP68 transducers and VARIOFIX mounting fixtures guarantee a long lifetime even under such difficult conditions. The measurement system of choice for such applications is the FLUXUS ADM 7407.

• FLUXUS^® ADM 7407 - Flow Meter for permanent installation
• Advantages
• Applications
• Technical Facts

The FLUXUS^® ADM 7407 is FLEXIM''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s flow meter for permanent installation in nearly any liquid flow metering application - especially in the industrial environment. Its non-intrusive measurement technology ensures a precise bi-directional, highly dynamic flow measurement over a wide turndown ratio.

Enclosed in a robust metal field housing, the ADM 7407 flow meter is completely water-tight and designed for usage in rough environments. As the transducers are mounted on the outside of the pipe wall in rugged VARIOFIX mounting fixtures, the system does not suffer from wear and tear or clogging, can''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''t be a risk for leaks and will not cause any pressure drops inside the pipe. Process interruptions or even production stops are a thing of the past with the ADM 7407.

Due to its matched and paired transducers as well as the internal temperature compensation (compliant to ANSI/ASME regulations), the measurement system is drift free and zero stable ensuring accurate readings. Moreover, as the transducer calibration data is automatically loaded by connecting the transducer to the transmitter the set-up times are significantly reduced. As of its exceptional dual-uP technology, the high number of measuring cycles per second and the adaptive signal processing, the FLUXUS^® ADM 7407 flow meter produces stable and reliable measuring results even under the most difficult conditions.

The liquid flow meter can be applied at inner pipe diameters ranging from 6 mm up to 12 m (no limitations on pipe wall thickness or material) and media temperatures from -40°C up to 200°C (-160° up to 400°C with the WaveInjector mounting fixture). The measurement is pressure independent and can take place on pipes of almost any material and on almost any liquid.

With up to two measurement channels, the FLUXUS ADM 7407 permanent liquid flow meter can be applied to difficult measurement points where other meters fail and is completely unaffected by viscosity, composition and toxicity of the medium itself as well as dust and humidity on the pipe wall outside. Due to innovative Hybrid trek Mode implemented in the flow computer, also liquids containing a high content of solid particles or gaseous loads can accurately be metered.

Further, with its wide range of electrical inputs and outputs, the FLUXUS ADM 7407 flow meter can handle a variety of process parameters within liquid flow metering applications. Input quantities such as temperature and/or pressure can be used by the flow meter, together with the measured flow, for the calculation of further quantities like thermal energy / BTU, mass flow rate, density, etc.

The FLUXUS ADM 7407 flow meter is also available in an ATEX Zone 2 / FM Class I, Div. II approved version, allowing its usage in the respective hazardous areas. FLEXIM also offers liquid flow meters for usage in ATEX Zone 1 environments, such as the FLUXUS ADM 8027 and FLUXUS ADM 8127 (for Offshore usage).

• FLUXUS^® ADM 7907 - The Rack Flow Meter
• Advantages
• Applications
• Technical Facts

The FLUXUS® ADM 7907 is the 19" inch rack version of the highly versatile FLUXUS ADM 7407 liquid flow meter.

Internally identical to the FLUXUS ADM 7407, its non-intrusive measurement technology ensures a precise bi-directional, highly dynamic flow measurement over a wide turndown ratio. As the transducers (available also as ATEX and FM approved versions) are mounted on the outside of the pipe wall and are enclosed in the stainless steel VARIOFIX mounting fixtures, the system does not suffer from wear and tear or clogging, can''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''t be a risk for leaks and will not cause any pressure drops inside the pipe. The transmitter itself, as a Rack version, can be situated in a control cabinet at quiet a distance from the actual measurement point and will be connected through junction boxes.

Due to its matched and paired transducers as well as the internal temperature compensation (compliant to ANSI/ASME regulations), the measurement system is drift free and zero stable ensuring highly accurate readings. Moreover, as the transducer calibration data is automatically loaded by connecting the transducer to the transmitter the set-up times are significantly reduced.

As of its exceptional dual-uP technology, the high number of measuring cycles per second and the adaptive signal processing, the FLUXUS® ADM 7907 flow meter produces stable and reliable measuring results even under difficult conditions.

The ADM 7907 liquid flow meter can be applied at inner pipe diameters ranging from 6 mm up to 12 m (no limitations on pipe wall thickness or material) and media temperatures from -40°C up to 200°C (-160° up to 400°C with the WaveInjector mounting fixture). The measurement is pressure independent and can take place on pipes of almost any material and on almost any liquid.

With up to two measurement channels, the FLUXUS ADM 7907 permanent liquid flow meter can also be applied to difficult measurement points and is completely unaffected by viscosity, composition and toxicity of the medium itself as well as dust and humidity on the pipe wall outside.

Further, with its wide range of electrical inputs and outputs, the FLUXUS ADM7907 flow meter can handle a variety of process parameters within liquid flow metering applications. Input quantities such as temperature and/or pressure can be used by the flow meter, together with the measured flow, for the calculation of further quantities like thermal energy / BTU, mass flow rate, density, etc.

The new FLUXUS F608 portable flow meter is based on the widely used, highly reliable and versatile F601, but has been specifically engineered for its use within hazardous areas and is covered by an ATEX certification.

Thus, users are not anymore obliged to obtain a Hot Work Permit, making the access to ATEX Zones much easier and less time consuming.

The extremely resistant carbon fibre housing, together with the rugged transducer design, ensures a high impact protection as well as resistance against oil, water and many other liquids. The F608 portable flow meter shares the same efficient battery management as the F601, offering over 14 hrs. of remote measurement time.

Moreover, the measurement system can be fully set-up in less than five minutes due to the intuitive user guidance and the automatic transducer recognition. Its application range is unrivalled - from pipes as small as 10mm up to 6500 mm inner diameter and temperatures ranging from -40°C to 200°C (with the WaveInjector solution even from -160°C to 400°C).

Being equipped with two flow channels, multiple In- and Outputs and an integrated data logger with a serial interface, the flowmeter is designed for direct usage in demanding environments, such as in the Upstream, Midstream and Downstream area as well as in the processing industries and the energy sector.

As known from all FLEXIM flow meters, also the F608 portable flow meter features a highly precise bi-directional measurement at fast and even very slow flow rates over a wide dynamic measurement range and is not prone to temperature and zero drift, being fully compliant to ANSI/ASME regulations.

However, the F608 is not only safe, accurate and reliable, but also very compact and lightweight, offering the user to even carry the complete measuring system as personal luggage for Offshore visits.

• An Expert for Hazardous Areas
• Advantages
• Applications
• Technical Facts

The FLUXUS ADM 8027 -
The ultrasonic flow meter for explosion hazardous areas

The FLUXUS ADM 8027 is FLEXIM''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s permanent flow meter for explosion hazard environments (being ATEX (IECEx) approved for usage in zones 1 and 2).
With its rugged, flameproof and water-tight field-enclosure, the flow meter - which can easily be operated by a magnetic pen without having open the housing - is especially designed for its usage in rough industrial environments such as in Chemical and Petrochemical plants or Refineries.

The FLUXUS ADM 8027 flow meter allows for an inherently bi-directional flow measurement of volumetric and mass flow rates of nearly any liquid media - ranging form crude oil to refined products - and can be equipped with various outputs for a sophisticated process control. As the ultrasonic transducers are mounted on the outside of the pipe wall, enclosed in the rugged stainless steel VARIOFIX mounting fixtures and connected to the transmitter through steel armored cables, the system does not suffer from wear, tear or clogging and can''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''t be a risk for leaks.

Due to its matched and paired transducers as well as the internal temperature compensation (compliant to ANSI/ASME regulations), the measurement system is drift free and zero stable. Moreover, as the transducers calibration data is automatically loaded by connecting the transducer to the transmitter, set-up times are significantly reduced. As of its exceptional dual-uP technology, the high number of measuring cycles per second and the adaptive signal processing, the FLUXUS® ADM 7407 flow meter produces stable and reliable measuring results even under the most difficult conditions.

The FLUXUS ADM 8027 flow meter can be applied at inner pipe diameters ranging from 10mm up to 6500mm (no limitations on pipe wall thickness or material) and media temperatures from -160°C up to 400°C (by usage of the high temperature mounting fixture WaveInjector).

With up to two measurement channels, the FLUXUS ADM 8027 flow meter can also be applied to difficult measurement points with non-ideal flow profiles. Even liquid streams with a high content of solids or gas bubbles are not a problem due to the innovative HybridTrek mode and the unique signal processing implemented into the flow computer.

• FLUXUS^® ADM 8127 - Offshore Flow Meter
• Advantages
• Applications
• Technical Facts

FLUXUS ADM 8127 - The ultrasonic flow meter for Offshore and Mining applications

The FLUXUS ADM 8127 flow meter for liquids is FLEXIM''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s solution for explosion hazard environments Offshore (being ATEX (IECEx) approved for usage in zones 1 and 2).
With a flameproof field-enclosure made entirely of stainless steel, the flow meter is permanently seaspray and seawater proof and can easily be operated by a magnet pen without having to open the housing.

The FLUXUS ADM 8127 flow meter allows for an inherently bi-directional flow measurement of volume and mass flow rates of nearly any liquid media - ranging form crude oil to refined products - and can be equipped with various outputs to be used for a sophisticated process control. As the ultrasonic transducers are mounted on the outside of the pipe wall, enclosed in the rugged stainless steel VARIOFIX C mounting fixture, the system does not suffer from wear, tear or clogging and can''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''t be a risk for leaks.

Due to its matched and paired transducers as well as the internal temperature compensation (compliant to ANSI/ASME regulations), the measurement system is drift free and zero stable. Moreover, as the transducers calibration data is automatically loaded by connecting the transducer to the transmitter, set-up times are significantly reduced. As of its exceptional dual-uP technology, the high number of measuring cycles per second and the adaptive signal processing, the FLUXUS ADM 8127 flow meter produces stable and reliable measuring results even under the most difficult conditions.

The ADM 8127 flow meter can be applied at inner pipe diameters ranging from 10 mm up to 6500 mm (no limitations on pipe wall thickness or material) and media temperatures from -40°C up to 400°C (by usage of the high temperature mounting fixture WaveInjector).

With up to two measurement channels, the FLUXUS ADM 8127 flow meter can also be applied to difficult measurement points with non-ideal flow profiles. Even liquid streams with a high content of solids or gas bubbles are not a problem due to the innovative HybridTrek mode implemented into the flow computer.

****************************

Lâm Hoài Diễm

[Cellphone]: 0916 635 755

[Email]: diem@songthanhcong.com 

Head office: 110 Hoa Cuc Street, Ward 7, Phu Nhuan District, HCMC 

TI + 84 8 35074676              FI +84 8 35173889 

WI www.stc-vietnam.com