Máy Đo Tĩnh Điện | Ksd-0303 | Ksd-0103S | Ksd-0103 | Ksd-0120 | Ksd-0108 | Ksd-0109 | Ksm-08 | Kasuga | Kasuga Vietnam | Pitesco Vietnam

KASUGA DENKI - KASUGA Vietnam - Pitesco Vietnam đại lý phân phối thiết bị KASUGA DENKI tại Việt Nam.

Trần Văn Ý

cellphone  +84 989 199 111

e maill: vany.pitesco@gmail.com

 Pitesco Vietnam JSC.,

Add: D5 Mieu Noi Resident, Dinh Tien Hoang St, W.3, Binh Thanh Dist, HCM City, Viet Nam

Tel  : 08 3517 6474/75

Fax  : 08 3517 6476

Web: www.pitesco.com

●Digital Low-Voltage Static Meter MODEL KSD-0303

The electrostatic tolerance of electronic devices is getting lower and lower, consequently lowering the target voltage for static management. A charge of 100 V or less, which cannot be measured by a conventional model, can be accurately measured within one volt by this model. If the measurement area is limited, this model allows you to measure a charge in a small area such as the surface of an LSI package.

- A low potential static charge that may still cause electrostatic destruction can be measured.
- By reducing the measurement distance, you can narrow the measurement area down to about 20 mm square and accurately measure the surface potential of a small electronic device.
- This model, consisting of a display unit and a measuring unit provided separately, allows you to conduct measurements in a confined area and immediately see the readouts.
- This model allows you to measure the potential distribution on anything from a small electronic part to a wide object.
- You can switch between peak hold and continuous measurement modes.

●Digital Static Meter MODEL KSD-0103S/0103

- Static charges from low potential to high potential can be measured.
- Being equipped with a measurement distance sensor, this model allows you to accurately measure the potential (KSD-0103).
- Even in continuous measurement mode, the hold function allows you to read a measurement by freezing the changing numeric values.
- This model has save and recall functions for the measured potential. Additionally, the printer output terminal allows you to manage potential data (KSD-0103S).
- With a probe that is provided separately, this model allows you to see the measurement results while continuing to measure the static potentials (KSD-0103S).
- In peak hold mode, you can easily identify the maximum value (KSD-0103S)  
 
 
 

●Two-Channel Static Monitor MODEL KSD-0120

- Since one controller can be connected to up to two channels of wide-potential sensors (KS-2100), this model allows you to construct a static monitor system at low cost.
- With compact sensor units, this monitor can be installed in a confined area in a manufacturing machine and enables continuous monitoring.
- This monitor can be set to issue alarms and operate in linkage with a manufacturing machine when a set potential is exceeded.
- This monitor has a failure indicator LED for the detecting sensor and can output an alarm to the outside.

●Explosion-Proof Static Meter MODEL KSD-0108

- This electrometer, possessing an intrinsically safe explosion-proof structure, can be used for measurement in a hazardous atmosphere.
- This compact, hand-held electrometer with a digital display is easy to use in a confined area such as the shop floor.
- Certificate numbers No. 53773  
 
 
 
 
 
 
 
 
 

●Static Monitor MODEL KSD-0109

- This model continuously monitors the occurrence of static electricity and, if the measured potential exceeds a set value, outputs a signal for control.
- The detector is in an intrinsically safe explosion-proof structure and can be installed in a hazardous location.
 
 
 

●Static Monitor MODEL KSM-08

- One controller of this monitor can be used to monitor the static electricity in up to eight locations.
- Potentials measured by the detectors are displayed for each channel in turn.
- If the measured potential exceeds a set value, this model outputs a signal for control.
- The detector is in an intrinsically safe explosion-proof structure and can be installed in a hazardous location.
- Certificate numbers No. 55782